Showing results: 346 - 360 of 582 items found.
-
Langer EMV-Technik GmbH
Used for EMI suppression in printed circuit boards during the development phase. The developer can use the E1 set to quickly identify the causes of burst and ESD interference. This allows the developer to design suitable measures to solve the causes of the interference. It can also be used to test the effectiveness of the measures taken.
-
Robson Technologies, Inc.
RTI designs and manufactures DUT boards for many types of special purpose test equipment including: ESD test systems, special purpose functional testers, automated curve trace equipment, as well as standard semiconductor test equipment. All designs are performed in-house using PCB design software (Mentor PADS, CAM350) and 3D mechanical design software (Solid Edge) if required. PCB fabrication is sub-contracted to one of our long-time fabrication partners.
-
CB49 -
CAMI Research Inc. (CableEye®)
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors. There are nine preset locations for automatic detection & display of 4, 6, 8, 10, 12, 14, 16, 18, and 20-pin connectors. Yet, any single set may be fitted with any combination of lower pin count connectors that total to 20 or less (e.g. a 14-pin with a 4-pin). Connectors soldered in non-preset positions will also appear graphically correct once they are mapped with PinMap (optional software). Sold as a set of two boards, each Micro-MaTch test board may be paired with other CableEye adapter boards to accommodate any combination of connectors.
-
1110748 -
Aries
Surface Mount to DIP Adapter for SOT-25, SOT-23A-6. Allows for breadboarding or substitution of microgate SOT-23A-6 and SOT-25 IC and transistor packages into .100 [2.54] pitch proto boards or PC boards. Solder masked top-side pads allow user to hand solder devices directly to topside of adapter with fewer problems of solder bridging. Longer male bottom pins are available at special request for easy use of probe clips. Large topside pads allow for soldering test pins, jumpers, etc. to top of adapter.
-
PCCextend 135 -
Sycard Technology
The PCCextend 135 allows a CardBus card under test to be powered from an external power supply. MOSFET switches automatically switch the external power to the CardBus card under test when the socket power is applied. The PCCextend 135 provides separate switches for VCC, VPP1 and VPP2. Fabricated on a six-layer board, the PCCextend 135 is designed to minimize signal degradation in the 33MHz CardBus environment.
-
Electro Mechanical Enterprises
Partial discharge instruments have two modes of Wide Band and Low Frequency. You can use it for Partial Discharge tests of High-Voltage Equipment, Insulation Materials, High-Frequency Equipment, and Power Semiconductor devices. Partial discharge Measuring Equipment can easily realize the test of Partial discharge on print-circuit boards, connectors, semiconductors, small motors and other insulation materials, to make a judgment on good / bad of them
-
W.L. Gore & Associates
For test applications that require consistent and highly repeatable measurements, GORE® Microwave/RF Assemblies for general purpose test applications provide reliable electrical performance with proven phase and amplitude stability. The smaller diameter and highly flexible, yet durable construction simplify the routing process while ensuring long-lasting electrical performance after installation, particularly in board-to-board and inside-the-box systems.
-
RF Test and Measurement Solutions, LLC
RFTMS is a leader in configuring systems to meet your needs, as well as designing load board, writing SW, and integrating the final solution. We do this for wafer test, packaged parts, and modules. RFTMS can address any level of integration that your parts employ, from a single functional block, i.e., Power Amplifier (PA) to System-on-a-Chip (SOIC). We test all sorts of RFICs.
-
VME-1129 -
Abaco Systems Inc
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
3916A -
Pomona Electronics
Dip Clip, 16 pin with Nickel Silver contacts. Pomona DIP Clip® test clips are designed for testing dual-in-line IC packages on PC boards. These devices incorporate many built-in features that assure a positive electrical connection as well as hands free testing.
-
igentic® 421t -
Sterner Automation Limited
Electronics customers require greater test flexibility to address the growing trend towards high-mix, low-volume printed circuit board (PCB) production. Sterner Automation is pleased to introduce the igentic® 421t, the next generation of automated test solution specially engineered to address these challenges. The igentic® 421t provides the flexibility, reliability and efficiency needed in one standard platform, allowing our customers to test multiple PCB's and significantly reduce individual product testing costs.
-
JT 2149/DAF -
JTAG Technologies Inc.
The JT 2149/DAF is a compact, mixed-signal (Digital/Analog/Frequency) measurement module for use in JTAG Technologies’ widely-used JT 2147 (QuadPod) signal conditioning interface. The DAF module has been designed to replace a regular TAP Pod and provides 28 measurement channels plus a clock generator. When connected to a circuit board via edge connector or test fixture/jig test pins, the module enhances standard digital boundary-scan tests by enabling a series of analog and frequency measurements to be made.
-
QT 200 NXG -
Qmax Test Technologies Pvt. Ltd.
QT 200 Nxg a Highly sophisticated ATE, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software.
-
KDL Series -
Bemco Inc.
The Bemco KDL series is designed for production testing of electronic circuit boards and completed electronic systems. They accept Bemco KDLC Carts that have a working area of 42 wide by 60 high by 48 deep suspended on insulated runners and casters 11 inches above the test area floor.
-
Components Corporation
The fabricators of SMT printed circuit boards may take advantage of the convenience of field testing with the unique loop design of Components Corporation's TP-107 and TP-108 series of surface mounted, printed circuit test points is now available in silver-plate for outstanding reliability. All products are RoHS and REACH compliant.